1. The air inlet hole is clogged or the air inlet hole (made of silicone) is squeezed and deformed during the assembly process.
2. Carbonisation of the atomizer core (cotton core) after a long time, and the formation of carbide on the surface of the heating wire affects the smoothness of the air intake.
3. Ceramic heating wire wrapped non-woven fabric process, non-woven fabric up and down height inconsistency or non-woven fabric exposed too long when a long time after the work of the non-woven fabric exposed part of the oil-impregnated adhering to the center of the ceramic heating wire in the middle of the impact of the intake smoothness.
1. If the LED shows normal but there is no smoke under the working condition of the vape, it may be caused by the welding of the output end of the battery pack, such as false welding or leakage welding.
2. If the battery rod does not detect an open or short circuit function, the atomizer itself is assembled abnormally, there is no resistance, and other bad (open or short circuit), will also lead to the atomizer does not working.
1. The output power of the battery cell is small, and cannot support the low-resistance atomizer to work normally (the resistance of the heating wire does not match the output of the battery).
2. Poor contact between the battery rod and the atomizer, high impedance, and unstable output.
3. The atomizer resistance value is too large, and low power, resulting in a small smoke volume Smoke oil (high/medium/low-temperature oil) and the atomizer heating temperature are unreasonable.
The first case:
1. The atomization design or assembly is unreasonable, the oil intake is large or leakage, the non-woven fabric can not be saturated with adsorption of smoke oil, the suction resistance is too large, the negative pressure inside the atomizer is large when re-smoking, and there is a risk that the smoke oil will be sucked out forcibly.
2. The atomizer’s central vent pipe is too small, so the smoke oil and condensation gather in the vent hole and cannot be removed or flow down.
3. After a long period without smoking, the smoke oil slowly seeps out and gathers in the center hole of the heating wire, when the first two puffs are sucked, the smoke oil will be sucked out of the vent hole instantly.
The second case:
1. The atomizer itself is designed or assembled in sealing abnormalities, continued in the oil leakage caused by.
2. If it is a repeatable oil injection or consumer oil injection, consumers use the process of injecting oil if the atomizer is not sealed promptly or sealed incorrectly will lead to atomizer oil leakage
Insensitive mainly for the microphone head start
1. Problems with the sealing of the microphone head, and air leakage.
2. The airway design is not reasonable, can not quickly trigger the microphone head to start.
1. The vape battery is generally not designed for low voltage alarm protection, the battery voltage has been lower than the minimum output protection voltage of PCBA and has not been able to drive the heating wire work.
2. PCBA designed low voltage protection warning voltage and the battery’s actual low voltage does not match.
1. Long time preheating, the smoke oil on the surface of the inner hole of the heating wire is in the state of high temperature boiling and easy to flow, the smoke oil will gather by gravity and seep down if you don’t throw it out the smoke oil in time, the oil will seep to the battery connection for a long time.
2. Bubbling in the oil inlet hole is a normal air pressure characteristic.
1. The normal operating voltage of the battery is between 3.0-4.2V, the use voltage is 3.8-4.2V when the power is used faster, of which 3.7V uses the longest running time, the power displays 100%, and the use of the voltage is correlated with each other because the battery displays the power of the arithmetic logic is not the same as that of the display of power, the display of the power will not be the same.
2. The consumption of battery power has a direct relationship with the size of the atomizer’s resistance value, which determines the speed of power consumption. The higher the resistance value of the atomizer, the higher the battery power consumption.
+86 18817743665
lena@dank-smoke.com
Address: No.3 Gold Road,Niuyang Village,Liaobu Town, Dongguan City,Guangdong Province,China
Product performance varies by use, temperature changes and other factors. DANK ® vape products are intended only to be used by adults aged 18 years (21 years where applicable) or over. DANK ® products are prohibited to sale to minors.
COPYRIGHT © 2024 Dongguan Dank Electronic Technology Co., LTD.